Check Out Winter Specials!

  • Overview
  • Specs
  • Accessories
  • Reviews
  • FAQ
  • Manuals & Downloads
  • Price/Add To Cart

 

OVERVIEW

Use with any HF rig

The XV transverters can be used with nearly any transceiver that covers the 28 to 30 MHz frequency range, including Elecraft's high-performance K3S, K3, K2. Single-port and dual-port IF connections work with almost any transceiver interface. IF transmit levels from -20 dBm to +39 dBm (.01 mW to 8 W) can be accommodated, with a constant-impedance IF termination for top performance. Reliable overload detection is included at the IF port to protect the mixer. Multiple transverters can be daisy-chained to a single IF transceiver, providing multi-band operation without cable rearrangement. A brightly-illuminated label clearly identifies which transverter is selected. There is also an auxiliary BNC connector on the rear panel that can be wired for a RX-only path at the XV output for split TX/RX antenna paths.

Easy to Build, Understand and Repair

Like Elecraft's transceivers, the XV Series transverters are completely modular, simplifying construction and alignment. The professionally-written, fully-illustrated manual will appeal to experienced as well as first-time builders. The kits are easy to assemble, featuring our "no-wires" construction, and all surface-mount parts used in the kit are preinstalled at the factory. Comprehensive Assembly and User Manual Our illustrated step-by-step assembly instructions include modular assembly and check out of each stage. Extensive theory of operation and troubleshooting sections are also provided.

Features

  • 28 - 30 MHz IF Frequency (28-32 MHz, XV432)
  • Built-in 10-segment LED bar graph wattmeter
  • Internal Fan for additional cooling.
  • Single-port and split dual-port IF connections allow use with almost any transceiver interface.
  • Rugged, attractive custom enclosure, 1.2h x 7.8w x 8.2d inches
  • Weight 3 lbs.
  • Efficient 12 Volt operation for home or field
  • Low-noise front end. 0.8 dB NF typical
  • Double-balanced +17 dBm diode mixer for excellent dynamic range
  • TX Power (SSB, CW) : 20 W (XV50, XV432), 25 W (XV144, XV222) 5W maximum recommended for high duty cycle FM & Data operation.
  • IF transmit levels from -20 dBm to +39 dBm (.01 mW to 8 W)
  • Constant-impedance IF termination for consistent performance.
  • External KEYIN and KEYOUT connectors for interfacing to most rigs
  • The XV50 uses a UHF connector. (UHF and N connectors are available from Elecraft if you wish to change them.)

The XV50 is packaged in a sleek, stackable, 1.2" tall enclosure.

 

 

 

SPECS

  • I.F. transmit levels from -20 dBm to +39 dBm (.01 mW to 8 W) can be accommodated.
  • Multiple transverters can be daisy chained to a single IF transceiver, providing multi-band operation without cable rearrangement.

General Size

  • Cabinet: 1.3” H x 7.8” W x 8.3” D (3.3 x 19.8 x 21 cm)
  • Overall: 1.5 H x 7.8 W x 9.5 D incl. feet and connectors (3.8 x 19.8 x 21 cm)
  • Weight: 2.5 lbs (1.1 kg)
  • Supply Voltage: 13.8 VDC
  • Current Drain: Receive: 250 mA (typical)
  • Transmit: 4 A typical
  • Frequency Ranges: XV50: 50 – 52 MHz
  • T/R Switching Time: 3 ms (typical)
  • T/R Key Input: Ground for transmit: must pull 5 volt logic level to within 0.5 volts of ground at < 1 ma
  • I.F. Overload Protection: Survives 100 watts RF input at the I.F. Port without damage with transverter un-keyed (in receive mode) 
  • Amplifier Key Output: Ground on transmit: 200 VDC at 1 A maximum
  • Connectors:
  • K2 or K3 Interface: DB9
  • Keying Line Input: RCA
  • Keying Line Output: RCA I
  • .F. In/Out: BNC
  • Aux (Rx-Only Ant): BNC
  • Antenna: SO-239 (UHF) on XV50 

TRANSMITTER

  • Power Out (50-ohm load): 20 watts
  • SSB/CW 10 watts continuous carrier modes
  • Minimum Supply Voltage Recommended: 12 VDC
  • Operating Modes: CW, SSB, AM, FM, Digital Modes
  • I.F. Input Frequency Range: 28 – 30 MHz (XV50, 144 & 222)  
  • I.F. Input Power Range: 0.01 mW (-20 dBm) to 8 watts (+ 39 dBm)
  • Harmonic Content: < - 60 dBc at 20 watts output

Receiver

  • Noise Figure: < 1 dB
  • Conversion Gain: 25 dB typical for XV50
  • Image Rejection: > 60 dB
  • 3rd-Order Intercept: +20 dBm (typical)

 

 

 

ACCESSORIES

  • XVOVN  High Stability Oven for internal crystal oscillator

 


     

    REVIEWS

     

     


      FAQ

      Q: Are the XV Series of transverters available as kits only?

      A: Yes.  However, we do have builders for hire.  Please contact sales@elecraft.com for more details.

      Q: When should I consider adding the XVOVN, high stability oscillator oven?

      A: For maximum stability, consider adding the high stability oven for CW, SSB/phone or digital modes.  It will not be needed for FM operation.

       

      Q: Can the XV series of transverters be used with other radios than Elecraft?

      A:  Yes.  The XV series of transverters are quite flexible for connections to most any transceiver that can operate in the 10 Meter band.